92 lines
3.5 KiB
Markdown
92 lines
3.5 KiB
Markdown
# PVC Oneshot Playbooks
|
|
|
|
This directory contains playbooks to assist in automating day-to-day maintenance of a PVC cluster. These playbooks can be used independent of the main `pvc.yml` and roles setup to automate tasks.
|
|
|
|
## `update-pvc-cluster.yml`
|
|
|
|
This playbook performs a sequential full upgrade on all nodes in a PVC cluster.
|
|
|
|
### Running the Playbook
|
|
|
|
```
|
|
$ ansible-playbook -i hosts -l [cluster] update-pvc-cluster.yml
|
|
```
|
|
|
|
### Caveats, Warnings and Notes
|
|
|
|
* Ensure the cluster is in Optimal health before executing this playbook; all nodes should be up and reachable and operating normally
|
|
|
|
* Be prepared to intervene if step 9 times out; OOB access may be required
|
|
|
|
* This playbook is safe to run against a given host multiple times (e.g. to rerun after a failure); if a reboot is not required, it will not be performed
|
|
|
|
### Process and Steps
|
|
|
|
For each host in the cluster sequentially, do:
|
|
|
|
1. Enable cluster maintenance mode
|
|
|
|
1. Perform a full apt update, upgrade, autoremove, and clean
|
|
|
|
1. Clean up obsolete kernels (`kernel-cleanup.sh`), packages/updated configuration files (`dpkg-cleanup.sh`), and the apt archive
|
|
|
|
1. Verify library freshness and kernel version; if these produce no warnings, go to step 14 (skip reboot)
|
|
|
|
1. Secondary the node, then wait 30 seconds
|
|
|
|
1. Flush the node, wait for all VMs to migrate, then wait 15 seconds
|
|
|
|
1. Stop and disable the `pvc-flush` daemon, stop the `pvcnoded` and `zookeeper` daemons, then wait 15 seconds
|
|
|
|
1. Set Ceph OSD `noout` and stop all Ceph OSD, monitor, and manager processes, then wait 30 seconds
|
|
|
|
1. Reboot the system and wait for it to come back up (maximum wait time of 1800 seconds)
|
|
|
|
1. Ensure all OSDs become active and all PGs recover, then unset Ceph OSD `noout`
|
|
|
|
1. Unflush the node, wait for all VMs to migrate, then wait 30 seconds
|
|
|
|
1. Start and enable the `pvc-flush` daemon
|
|
|
|
1. Reset any systemd failures
|
|
|
|
1. Disable cluster maintenance mode, then wait 30 seconds
|
|
|
|
## `upgrade-pvc-daemons.yml`
|
|
|
|
This playbook performs a sequential upgrade of the PVC software daemons via apt on all nodes in a PVC cluster. This is a less invasive update process than the `update-pvc-cluster.yml` playbook as it does not flush or reboot the nodes, but does restart all PVC daemons (`pvcnoded`, `pvcapid`, and `pvcapid-worker`).
|
|
|
|
### Running the Playbook
|
|
|
|
```
|
|
$ ansible-playbook -i hosts -l [cluster] upgrade-pvc-daemons.yml
|
|
```
|
|
|
|
### Caveats, Warnings, and Notes
|
|
|
|
* Ensure the cluster is in Optimal health before executing this playbook; all nodes should be up and reachable and operating normally
|
|
|
|
* This playbook is safe to run against a given host multiple times; if service restarts are not required, they will not be performed
|
|
|
|
* This playbook should only be used in exceptional circumstances when performing a full `update-pvc-cluster.yml` would be too disruptive; it is always preferable to update all packages and reboot the nodes instead
|
|
|
|
### Process and Steps
|
|
|
|
For each node in the cluster sequentially, do:
|
|
|
|
1. Enable cluster maintenance mode
|
|
|
|
1. Perform an apt update, and install the 4 PVC packages (`pvc-client-cli`, `pvc-daemon-common`, `pvc-daemon-api`, `pvc-daemon-node`)
|
|
|
|
1. Clean up the apt archive
|
|
|
|
1. Verify if packages changed; if not, go to step 8 (skip restarts)
|
|
|
|
1. Secondary the node, then wait 30 seconds
|
|
|
|
1. Restart both active PVC daemons (`pvcapid-worker`, `pvcnoded`), then wait 60 seconds; since the node is not the primary coordinator, `pvcapid` will not be running
|
|
|
|
1. Verify daemons are running
|
|
|
|
1. Disble cluster maintenance mode, then wait 30 seconds
|